Everything is measured in dots
Morse code has a single unit of time, the length of one dot, and all the other timing is a multiple of it. The international standard, ITU-R M.1677-1, sets out the proportions:
- A dot lasts 1 unit.
- A dash lasts 3 units.
- The silence between signals within a letter is 1 unit.
- The silence between letters is 3 units.
- The silence between words is 7 units.
The Play button uses a 100 millisecond unit and a 600 Hz tone, in the range many operators find comfortable. Written Morse has no way of showing silence, so by convention a space stands for the gap between letters and a slash stands for the gap between words.
Why PARIS sets the speed
Words vary in length, so "words per minute" needs a reference word. Operators use PARIS, which takes exactly 50 units including the gap after it:
P .--. 1+1+3+1+3+1+1 = 11
A .- 1+1+3 = 5
R .-. 1+1+3+1+1 = 7
I .. 1+1+1 = 3
S ... 1+1+1+1+1 = 5
4 letter gaps x 3 = 12
1 word gap x 7 = 7
Total = 50
That gives a simple formula: words per minute = 1200 ÷ the unit in milliseconds. A 100 ms unit is 12 words per minute, the speed of Play on this page. A 60 ms unit would be 20, a typical speed for an experienced amateur.
Decoding by hand
Take this message and split it at the spaces:
-- --- .-. ... .
Using the reference table on this page, -- is M, --- is O, .-. is R, ... is S and . is E, spelling MORSE. Paste it into the Morse Code box and you will get the same answer. The spaces are essential, because the code is not self-delimiting. The pattern .- is A, while . - with a gap is E followed by T, and .-- is W, whereas . - - is ETT.
If you paste a group the table does not contain, such as a long run with its gaps lost, the group is left in the output unchanged, which makes the point where a transcription went wrong easy to spot.
Short codes for common letters
The most frequent English letters have the shortest codes: E is a single dot and T a single dash, while rare letters like Q and Y take four signals with three dashes. The story usually told is that Alfred Vail, Samuel Morse's partner, estimated letter frequency by counting the type in a printer's case. Morse and Vail's first public long-distance message, "What hath God wrought", went from Washington to Baltimore in 1844.
Their original American Morse is not the code in use today. It relied on internal spaces and dashes of different lengths, which worked for clicking telegraph sounders but was error-prone on radio. Friedrich Gerke's simplified 1848 version became the basis of International Morse, adopted at the 1865 International Telegraph Conference in Paris. This translator uses the international code.
SOS is not an abbreviation
SOS does not stand for "save our souls". The signal was chosen for its unmistakable rhythm and was adopted at the 1906 International Radiotelegraph Convention in Berlin, taking effect in 1908. Operators send it as one unbroken sequence with no letter gaps, a form called a prosign. Written as ...---... without spaces, it will not decode here, since this page reads spaces as letter boundaries. Typing SOS produces the separated form, ... --- ..., which is how it is normally shown in print.
Where Morse survives
The maritime world stopped relying on it when the Global Maritime Distress and Safety System came fully into force in 1999. In the United States, the FCC removed the Morse exam from amateur licensing in 2007. Even so, many radio amateurs still choose it, because a narrow, on-off signal can get through when weak conditions defeat voice. VOR and other radio navigation beacons continue to identify themselves with a repeating two- or three-letter Morse code, and pilots check it to confirm they have tuned the right station.
The translator covers letters, digits and punctuation. The ITU standard includes . , : ? ' - / ( ) = + " and @. The symbols ! & ; _ and $ are also supported, but they come from operator convention and not from that standard, so a receiver may not know them. Accented letters and other scripts have no entry here and pass through unchanged.